Oscilloscopes and Probes
Automotive
Key specifications
- WiFi / LAN / USB connected
- 14 bit (0.006 %) resolution (16 bit enhanced resolution)
- Up to 1 GSa/s sampling
- 250 MHz bandwidth
- Up to 200 MSa/s continuous streaming
- Up to 256 Mpoints memory per channel
- 0.25 % DC vertical accuracy, 0.1 % typical
- 1 ppm time base accuracy
This powerful automotive WiFi oscilloscope combines fast sampling up to 1 GSa/s with high resolutions of 12, 14 and 16 bit and a large memory of 64 Mpoints per channel with four differential channels. Additionally, the automotive WiFi oscilloscope supports continuous streaming measurements up to 200 MSa/s.
 |
 |
 |
 |
 |
The Automotive Test Scope ATS610004DW-XMSG is delivered with SureConnect connection test and resistance measurement on each channel.
Also, the Automotive Test Scope ATS610004DW-XMSG is delivered with SafeGround. With SafeGround you can switch the differential inputs of the Automotive Test Scope ATS610004DW-XMSG into single ended inputs with ground protection. It allows to make measurements using standard attenuating probes or standard shielded measure leads and protects the scope when a short circuit to ground is created.
Specifications
Acquisition system | ||||
|---|---|---|---|---|
| Number of input channels | 4 analog | |||
| CH1, CH2, CH3, CH4 | Isolated female BNC | |||
| Type | Differential input | |||
| Resolution | User selectable in software | |||
| Native | 8, 12, 14 bit | |||
| Enhanced | 16 bit | |||
| DC Accuracy | 0.25 % (0.1 % typical) of full scale ± 1 LSB at 20°C to 25°C To achieve rated accuracy, allow the instrument to settle for 20 minutes. When subjected to extreme temperatures, allow additional time for internal temperatures to stabilize. | |||
| Ranges (full scale) | ±200 mV ±400 mV ±800 mV | ±2 V ±4 V ±8 V | ±20 V ±40 V ±80 V | |
| Coupling | AC/DC | |||
| Impedance | 2 MOhm / 12 pF ± 1 % 1 MOhm / 20 pF ± 1 % when SafeGround enabled | |||
| Noise (in 200 mV range) | 300 µVrms | |||
| Maximum voltage | 200 V (DC + AC peak < 10 kHz) | |||
| Maximum Common Mode voltage | 200 mV to 800 mV ranges : 2 V 2 V to 8 V ranges : 20 V 20 V to 80 V ranges : 200 V | |||
| Common Mode Rejection Ratio | -47 dB | |||
| Bandwidth | ||||
| -3dB at 75 % of full scale input | 250 MHz | |||
| Limit, selectable per channel | Off (250 MHz), 150 MHz, 100 MHz, 50 MHz | |||
| AC coupling cut off frequency (-3dB) | ±1.5 Hz | |||
| SureConnect | ||||
| Maximum voltage on connection | 200 V (DC + AC peak < 10 kHz) | |||
| Resistance measurement | ||||
| Ranges (Full scale) | 1 kΩ 2 kΩ 5 kΩ | 10 kΩ 20 kΩ 50 kΩ | 100 kΩ 200 kΩ 500 kΩ | 1 MΩ 2 MΩ |
| Accuracy | 1 % of full scale | |||
| Response time (to 95%) | < 10 µs | |||
| SafeGround | ||||
| Maximum voltage on connection | 200 V (DC + AC peak < 10 kHz) | |||
| Maximum switch off current | 500 mA | |||
| Response time | < 100 ns | |||
| Maximum sampling rate | 8 bit | 12 bit | 14 bit | 16 bit |
| measuring one channel | 1 GSa/s | 500 MSa/s | 100 MSa/s | 6.25 MSa/s |
| measuring two channels | 500 MSa/s | 200 MSa/s | 100 MSa/s | 6.25 MSa/s |
| measuring three or four channels | 200 MSa/s | 100 MSa/s | 100 MSa/s | 6.25 MSa/s |
| Maximum streaming rate 1 | 8 bit | 12 bit | 14 bit | 16 bit |
| 8 bit | ||||
| measuring one channel | 200 MSa/s 2 | 100 MSa/s 3 | 100 MSa/s 3 | 6.25 MSa/s 6 |
| measuring two channels | 100 MSa/s 3 | 50 MSa/s 4 | 50 MSa/s 4 | 6.25 MSa/s 6 |
| measuring three or four channels | 50 MSa/s 4 | 25 MSa/s 5 | 25 MSa/s 5 | 6.25 MSa/s 6 |
| ||||
| Sampling clock source | ||||
| Internal | TCXO | |||
| Accuracy | ± 0.0001 % | |||
| Stability | ± 1 ppm over 0°C to 55°C | |||
| Time base aging | ±1 ppm/year | |||
| External | LVDS, on CMI connectors | |||
| Input frequency | 10 MHz ± 1 % 16.369 MHz ± 1 % | |||
| Memory | via USB | via WiFi/LAN | ||
| 8 bit resolution | ||||
| Measuring one channel | 256 MSa per channel | 64 MSa per channel | ||
| Measuring two channels | 128 MSa per channel | 32 MSa per channel | ||
| Measuring three or four channels | 64 MSa per channel | 16 MSa per channel | ||
| 12, 14, 16 bit resolution | ||||
| Measuring one channel | 128 MSa per channel | 32 MSa per channel | ||
| Measuring two channels | 64 MSa per channel | 16 MSa per channel | ||
| Measuring three or four channels | 32 MSa per channel | 8 MSa per channel | ||
| Trigger | Only available in scope/block mode, not in streaming mode | |||
| System | Digital, 2 levels | |||
| Source | CH1, CH2, CH3, CH4, OR, digital external | |||
| Trigger modes | Rising edge, Falling edge, Any edge Inside window, Outside window, Enter window, Exit window (time conditions only on Ch1) Pulse width (only on Ch1) Interval (only on Ch1) | |||
| Level adjustment | 0 to 100 % of full scale | |||
| Hysteresis adjustment | 0 to 100 % of full scale | |||
| Resolution | 0.006 % (14, 16 bits) / 0.025% (12 bits) | |||
| Pre trigger | 0 to selected record length, 1 sample resolution | |||
| Post trigger | 0 to selected record length, 1 sample resolution | |||
| Trigger hold-off | 0 to 63 MSamples, 1 sample resolution | |||
| Trigger delay | 0 to 8 GSamples, 1 sample resolution | |||
| Digital external trigger | ||||
| Input | Extension connector pins 1 and 2 | |||
| Range | 0 to 2.5 V (TTL) | |||
| Coupling | DC | |||
| Jitter | ≤ 1 sample | |||
Multi-instrument synchronization | ||||
| Using CMI | Synchronizing instruments via CMI is available when all instruments are connected via USB. | |||
| Maximum number of instruments | Limited by number of available USB ports | |||
| Synchronization accuracy | 0 ppm | |||
| CMI interface | 2x, CMI 1, CMI 2 | |||
| Required coupling cable | TP-C50H Coupling cable CMI | |||
| Maximum coupling cable length | 50 cm | |||
| Using WCMI | Synchronizing instruments via WCMI is available when instruments are connected via USB, LAN and WiFi. | |||
| Maximum number of instruments | No limitation | |||
| Required coupling module | WCMI - 8, WCMI - 9 | |||
| Clock synchronization accuracy | ≤ 1 ppm, typical ≤ 0.2 ppm | |||
| Trigger jitter at sample rate 1 | ≤ 1 MSa/s | > 1 MSa/s | ||
| 2 x "5" | ≤ ±2 samples | ≤ ±2 µs | ||
| "5" and "6" | ||||
| Trigger source "5" | ≤ ±2 samples | ≤ ±2 µs | ||
| Trigger source "6" | ≤ ±8 samples | ≤ ±8 µs | ||
| 2 x "6" | ≤ ±8 samples | ≤ ±8 µs | ||
Probe calibration | ||||
| Output | Extension connector pins 3 (signal) and 6 (ground) | |||
| Signal | Square wave | |||
| Level | -1 V to 1 V | |||
| Frequency | 1 kHz | |||
Interface | ||||
| Interface | ||||
| USB | USB 3.0 SuperSpeed (5 Gbit/s); (USB 2.0 HighSpeed compatible) | |||
| Network | 1 Gbps | |||
| WiFi | 802.11 | |||
Power Requirements | ||||
| Power | From USB, external input or built-in battery | |||
| Consumption | 12 VDC 2 A max | |||
| External power | From power adapter | |||
| Internal battery | Li-ion | |||
| Capacity | 7000 mAh, 3.7 V | |||
| Weight | 160 g | |||
Physical | ||||
| Instrument | ||||
| Height | 44 mm (1.7 inch) | |||
| Length | 187 mm (6.7 inch) | |||
| Width | 215 mm (5.2 inch) | |||
| Weight | 791 g (27.9 ounce) | |||
| USB cord length | 1.5 m (59 inch) | |||
I/O connectors | ||||
| Channel 1, 2, 3, 4 | Isolated BNC, female | |||
| LAN | RJ45 socket | |||
| USB | USB 3.0 type B Super Speed socket | |||
| Extension connector | D-sub 9 pins female | |||
| Power | 3.5 mm power socket | |||
| CMI connectors | 2 x HDMI type C socket | |||
System requirements | ||||
| PC I/O connection | USB 2.0, USB 3.0 or USB 3.1 RJ45 WiFi | |||
| Operating system | Windows 10 / 11, 64 bits Linux (via own software using the libtiepie-hw SDK) | |||
Environmental conditions | ||||
| Operating | ||||
| Ambient temperature | 20°C to 25°C for rated accuracy (10°C to 40°C without specifications) | |||
| Relative humidity | 10 % to 90 %, non condensing | |||
| Charging | ||||
| Ambient temperature | 0°C to 35°C | |||
| Relative humidity | 10 % to 90 %, non condensing | |||
| Storage | ||||
| Ambient temperature | 0°C to 35°C | |||
| Relative humidity | 5 % to 95 %, non condensing | |||
Certifications and Compliances | ||||
| CE mark compliance | Yes | |||
| RoHS | Yes | |||
| EN 55011:2009/A1:2010 | Yes | |||
| EN 55022:2006/A1:2007 | Yes | |||
| EN 61000-6-1:2007 | Yes | |||
| EN 61000-6-3:2007 | Yes | |||
Package contents | ||||
| Carry case | Carry case BB453 | |||
| Instrument | Automotive Test Scope ATS610004DW-XMSG | |||
| Measure leads | 4 x Measure lead TP-C1812B, Differential BNC -> 4 mm banana plug | |||
| Differential attenuator | 4 x Differential attenuator TP-DA10 | |||
| Alligator clips, large | Alligator Clip TP-AC80I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 large alligator clips | |||
| Alligator clips, medium | Alligator Clip TP-AC10I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 medium alligator clips | |||
| Alligator clips, small | Alligator Clip TP-AC5 - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 small alligator clips | |||
| Accessories | Ground compensation Cable TP-GCC150 Handyscope / WiFiScope power supply USB3 cable, 1.5 m long network cable, 3 m long Probe compensation cable TP-DB9-BNC-30 | |||
| Software | for Windows 10 / 11, 64 bits, via website | |||
| Drivers | for Windows 10 / 11, 64 bits, via website | |||
| Manuals | instrument manual and software user's manuals color printed and digital, via website | |||
Optional Accessories | ||||
| Optional accessories for the Automotive Test Scope ATS610004DW-XMSG need to be ordered separately | ||||
| Oscilloscope probe | Oscilloscope Probe 1:1-1:10 - HP-3250I | |||
| Measure lead single ended | Measure lead TP-BNCI-100 | |||
Customer service | ||||
| TiePie engineering instruments are designed, manufactured and tested to provide high reliability. In the unlikely event you experience difficulties, the TiePie engineering instruments are fully warranted for two years. | ||||
| This warranty includes | All parts and labor (excluding probes and/or measure leads and/or batteries) Warranty on batteries is 6 months. No charge for return shipping Long-term 7 year support Upgrade to the latest software at no charge | |||
